Polyethylene blade yarn — PE is the fibre behind the football artificial grass face because it stays soft underfoot and springs back after a stud presses it down, and it holds pigment well, so the green stays green instead of greying out.
Dense tufting at 10,500 — the blades are packed closely enough to hide the dark backing even when the pile is bent, so the surface reads as realistic artificial grass rather than a mat.
PP net plus SBR latex backing — the net stops the roll stretching out of square when it is unrolled in the sun, and the latex locks the tufts in place so seams stay closed and the edge does not fray as it is cut.
Perforated underside — the backing is perforated, visible along the sample edges, so water passes through the sheet into the base rather than sitting on the surface.
Clean cut edges — the roll trims straight with a hand knife, which shortens seaming time and keeps joints tight over a long pitch.
Performance Advantages
What you notice over a season is how little the surface changes. The 45 mm pile keeps a consistent bounce and roll, so a pass along the ground behaves the same in week twenty as in week one; the fibres are dense enough that studs do not leave a permanent pattern in the traffic lanes, and the green stays even instead of wearing through to a darker underlayer.
Water is the other test. Because the backing is perforated, rain passes through the sheet into the base rather than sheeting across the pitch, and with no soil to churn a field stays playable in conditions that would close a natural grass surface. Underfoot, the pile gives a cushioning layer over the compacted base, which is what makes a 45 mm surface comfortable through a full training session.
Compared with the shorter landscaping rolls in our range, 45 mm artificial grass gives a football surface the depth it needs for slide tackles and for the ball to sit up predictably; compared with natural grass it removes the mid-season renovation window and the daily dependence on weather.
Visually the surface holds up as well as it plays: the pile stands upright rather than lying flat after brushing, the seams sit low, and the colour stays even across the roll, which is what separates realistic artificial grass from a surface that looks tired after two seasons.
Pitch Installation Sequence
Prepare the site — clear the area, strip any old surface, set the levels and fix timber, concrete or steel edge restraints so the perimeter cannot spread under load.
Measure and mark out — run string lines for the pitch, check the diagonals for square and mark the line positions. Set the pile direction now as well: keep every roll running the same way and plan seams away from the main sight line.
Lay the base — compacted aggregate is the usual base for outdoor artificial turf, laid with a fall to the drainage points; asphalt or concrete is used where the surface must be firmer or the site sits above a structure. Confirm the base build with your installer against the use the field will get.
Roll out and condition — lay the rolls on the base in the planned direction and let the turf relax before trimming. Cutting cold, tight turf is how short rolls and open seams happen.
Cut, seam and fix — trim to the edge restraints, join the rolls with seaming tape and adhesive, and fix the perimeter. The clean cut edge on the roll is what keeps the joint tight.
Infill with silica sand and rubber granules — spread the sand first, then the rubber, in passes, brushing each layer down between the blades rather than leaving it on top. The quantity depends on the pile and the use, so confirm the rate for the field before the bags are ordered.
Brush, inspect and hand over — power-brush against the pile, clear the debris, check every seam and fixing, and walk the surface with the client. Installation is carried out by your own crew or a local installer; we support the work with the roll layout, pile direction and seam details for your order, along with the installation guidance we publish for football artificial grass.
Applications
Club match pitches — full-size and small-sided grounds that carry weekly fixtures; pitch dimensions and line positions are set out before the turf is cut, so decide them at the planning stage.
Full-size soccer fields — an artificial grass soccer field at 45 mm gives the depth needed for slide tackles and a true ball roll, and the same roll is used for run-offs and technical areas.
Training grounds and warm-up zones — the high-traffic areas where a natural surface would wear to mud by mid-season; the dense pile takes repeated sessions without thinning.
School and college sports fields — one surface for PE lessons, after-school clubs and weekend fixtures, with no mowing schedule to fit around the timetable.
Community multi-use areas — marked for more than one sport so a single surface serves football, training and general recreation.
Stadium surrounds and venue landscaping — pitch perimeter, concourse edges, clubhouse frontage and courtyards, where the turf keeps mud off walkways and stays green where mown grass will not. The PP and PE fiber construction and PP net/SBR latex backing help the turf stay dimensionally stable under mechanical stress and allow installation over a range of base substrates and drainage layouts. The same build is made to adapt to different climatic zones and usage conditions. This is a 45 mm football turf built for surfaces that take real traffic: school pitches, club grounds, training areas and multi-use sports fields. The face is a dense polyethylene pile in bright green, and underneath it sits a PP net bonded with SBR latex — a build chosen so the roll keeps its shape when it is pulled out across a pitch in the sun, and so rain passes through instead of pooling on the surface. Close up, the blades are tight and upright and the cut edges stay clean, which is what makes a straight seam possible on site. We are a football turf supplier and artificial grass manufacturer working out of Nantong, Jiangsu, and we quote each model on its own figures rather than on a generic description: model QS009 carries a 45 mm pile, 10,500 density and 8,800 dtex yarn. Those are the numbers that go on the quotation, and the numbers we check against the approved sample before the rolls are packed. Most buyers come to this 45 mm artificial grass for one of two jobs: replacing worn natural grass on a school or club field, or upgrading an older synthetic surface that has flattened and faded. The deeper pile is the point — it takes studs, holds a line marking, and keeps the ball rolling consistently through a full season rather than a few weeks. Colours are made to order, so a club can match its own shade instead of accepting a stock green. It also works as indoor outdoor artificial grass in areas without natural sunlight or adequate irrigation, and it can be integrated with existing irrigation and drainage systems to support lower lifecycle maintenance costs. In residential gardens it provides a durable lawn alternative without soil or water dependency, and contractors can install it quickly over standalone substrates or alongside automated irrigation. Its surface is designed to meet homeowner expectations and local standards for sustainable garden development.
Maintenance & Care
Brushing is the main habit on any synthetic pitch. A stiff brush or a rotary brush run against the pile lifts flattened fibres and pushes the infill back into the busy zones that traffic empties — goalmouths, the centre circle, the touchline where players turn. Once a month is enough on a school field; a club surface used several times a week benefits from a weekly pass over the worn areas. Between brushes the work is debris. Leaves, litter, broken glass and blown sand all need lifting before they work down into the pile, and the drainage outlets at the low points of the base need to stay clear so outdoor artificial turf can shed water the way it was designed to. A wash down with water handles dust and bird droppings. Chewing gum and oil need a little patience: freeze gum and lift it off, blot oil with an absorbent before washing the area with a mild detergent, and keep solvents away from the pile. Infill settles over a season, so top it back up to the level it was installed at rather than letting the blades flatten, and check seams and edge fixings at the same time — a lifted edge is quick to repair and expensive to leave. What the surface does over the years is hold its colour and its pile height, provided the brushing and top-ups happen. The dense fiber arrangement balances softness with load-bearing capacity and user safety in high-traffic areas, while easy cleaning and color retention help lower operating costs and improve return on investment.
Specifications
Model
QS009
Pile height
45 mm
Blade fibre
Polyethylene (PE)
Yarn weight
8,800 dtex
Density
10,500 lbs
Backing
PP net + SBR latex
Face colour
Bright green, made to order
Pile character
Dense upright blades on a dark perforated backing
Primary use
Football pitches, training grounds and multi-use sports areas
Installation
Loose laid on a prepared base, seamed and infilled
Colour and Roll Options
Colour matched before production — send the club colour or the shade you are working to and it is matched at the sample stage; the shade you approve is the one the bulk run repeats across every roll in the order.
Pile, density and backing discussed against the job — a field used daily and one hosting weekend fixtures do not need the same build. Tell us how the surface will be used and we will say which specification changes and what stays the same.
Roll size and packing set with the order — roll length is agreed together with the order so it fits both the container plan and the way your crew lays and seams on site.
Your own labelling — rolls and packaging can carry your brand, which is how distributors sell under their own name. As an artificial grass manufacturer we produce to the label, not just to the colour.
Sample approval first — ask your sales contact about sample availability and judge colour, pile and backing against the sample before bulk production begins.
Ordering & Delivery
Minimum order — 2,000 sqm, which is one container.
Production time — 7–15 days once the specifications and order details are confirmed.
Sea freight — about 30 days by sea; sailing is booked against your destination port and the date you need the container on site.
Packing — rolls wound on cardboard cores, wrapped and labelled, then loaded to a container plan agreed with you.
Price — the indicative range for this model is $2.50–5.50 per square metre; the figure for your specification and volume is confirmed on the quotation.
Warranty — the model is quoted with a five-year manufacturing warranty; ask your sales contact for the cover and claim process that apply to your order.
What to send for a quotation — pitch dimensions or area in square metres, colour, pile and backing, destination port, and any packing or labelling requirement.
One contact from quotation to loading — as a football turf supplier we follow the order through production checks, inspection and booking from Nantong.
Repeat and mixed orders — 45 mm artificial grass wholesale runs combine with other models from our range in the same container, so one shipment can cover a whole site.
A pitch rarely arrives on its own. Around the field there is usually a warm-up strip, a practice green by the clubhouse or a landscaped edge along the car park, and those are the jobs our companion models cover. QS071 is the 45 mm soccer field turf we quote when a club needs a second artificial grass soccer field alongside the main pitch. QS070 is the 45 mm sport outdoor turf used for multi-sport and general sports surfaces. QS072 is a 10 mm golf turf for practice and chipping areas, and QS073 is an 8 mm soft putting green for the clubhouse green. Set against those, this roll is the match surface: 45 mm of football artificial grass with the density to hold a line marking and the backing to drain a wet week. When a project includes more than one surface, send us the area for each and we will set the specification out surface by surface, so the pitch, the practice green and the landscape edges are quoted together and packed together.
Quality Control & Inspection
Working as an export specialist from Nantong, Jiangsu, we build quality checks into every stage of an order rather than leaving them to the end. Before bulk production, yarn, colour and backing are confirmed against the approved sample; during production we check pile height, density, tufting and backing at the supplier; before loading, rolls, colours and packing are checked again and the inspection record is shared with you. If you prefer an independent eye, we can coordinate third-party inspection such as SGS or BV, book the visit and follow up on any defects found. Faulty rolls are replaced or credited before shipment, and each carton leaves with its packing list and inspection sheet.
FAQ
What materials are used to make your artificial grass?
The face is polyethylene (PE) blade yarn, tufted densely into a primary backing, and the sheet is finished underneath with a PP net and an SBR latex layer. PE keeps the blades soft and springy underfoot and holds colour well; the net stops the roll stretching out of square on site; the latex locks the tufts and stiffens the edge so it cuts and seams cleanly. As an artificial grass manufacturer we buy and inspect those three components together, because good yarn on a weak backing still gives you a surface that ripples.
Can I customize the colour and specifications of the artificial grass?
Yes — colour, pile height, density, backing and roll size can all be set for a project, and we will confirm what is practical on this model before you commit. Colour is the one most buyers change, usually to match a club shade or a house brand, and it is approved at the sample stage. Pile and density changes affect roll weight, price and production time, so settle those with your sales contact before the order is placed.
Is this turf built for a full-size pitch or for smaller training areas?
Both, with different bases and infill depths behind them. A full-size artificial grass soccer field carries continuous play, so the base, the seam layout and the infill are planned across the whole surface; a training area or small-sided pitch can be built to a simpler base. The roll is the same 45 mm product either way — what changes is the groundwork and the fixing detail, which your installer should confirm before the turf is cut.
Does 45 mm turf need infill?
For football use, yes. A 45 mm artificial grass surface is normally dressed with silica sand and rubber granules so the pile stays upright under studs and the ball rolls predictably. The quantity depends on the pile and on how hard the pitch will be used, so confirm the rate for your field before the bags are ordered — under-filling leaves the blades flattened in the first season.
How realistic does the turf look up close?
The blades are tufted in two tones, a deeper green at the root and a brighter tip, so the surface shifts with the light instead of reading as one flat colour, and the pile is dense enough that the dark backing stays hidden. From a few metres away it reads as realistic artificial grass; from directly above you see the tuft lines, as you would on any synthetic pitch. If appearance is critical, judge it on a sample under the light where it will be installed.
Can it be laid over an existing hard surface?
Usually yes, provided the surface is sound, level and drains. Outdoor artificial turf is laid over compacted aggregate, asphalt or concrete with a fall towards the drainage points; what you cannot do is lay it over broken slabs, soft ground or a base that holds water, because the turf follows every dip. Check the base, the edge restraints and the drainage before the rolls arrive, and confirm the build with your installer.