This is a 20 mm pet turf from our pet range — a short, dense cut pile on a PP net and SBR latex backing, made for the places where dogs actually spend their day: garden runs, kennel yards, day-care exercise areas, grooming salons and the outdoor pens behind a vet clinic. The pile is firm enough to take claws and repeated brushing, and short enough that a scoop, a hose and a stiff broom handle almost every clean-up. The modern style finish is about how the surface reads once it is laid. It looks like a closely mown lawn rather than a shaggy rug, so it sits properly beside grey paving, composite decking, render and powder-coated fencing — on a house, at the front of a showroom, or along the entrance to a boarding facility where clients judge the place before they reach the door. Most buyers of this model are not laying a patch for one dog. They are distributors adding a line of wholesale artificial grass for pets to a catalogue, kennel and day-care operators refitting a yard, groomers fitting an exercise run, or landscape contractors building a pet area for a client. One specification has to work across all of those jobs, in a colour the buyer can defend to their own customer. As a pet turf manufacturer, we would rather you ask the awkward questions early — pile height, colour under your own light, how the seams will fall — than find them after the container lands.
Performance in Pet Areas
Short pile, faster clean-ups. At 20 mm the fibres stand upright and leave little space for debris to work down to the backing, so waste lifts off with a scoop and a rinse instead of being teased out of a deep thatch.
Soft underfoot without a spongy feel. The PP and PE blend gives a soft artificial grass surface that is comfortable for a dog to lie on and for staff standing at a gate through a shift. The PE side of the blend carries the softer hand-feel while the PP keeps the pile resilient under repeated trampling.
Fibres that come back up. When a dog turns sharply or digs at a corner, brush the pile with a stiff broom and the fibres lift back towards upright instead of staying matted flat.
A backing that holds its shape. The PP net and SBR latex layer gives the roll a firm, stable base, so the turf stays flat once it is laid and the edges do not curl where dogs cross them all day.
Wear appears in one place first. Every run has a gateway, a water bowl or a favourite patch by the fence, and that is where the surface takes the traffic. Plan a hard-standing pad or a paving edge at the gate and expect to brush the worn patch more often than the rest.
Built for dogs rather than lawns. Claws, digging and constant moisture put artificial turf for dogs under a different kind of load from a garden lawn — the load a pet turf manufacturer designs around. A short cut pile handles that pattern better than a long decorative pile: less material to trap debris, less depth to hold moisture, and a surface that still reads as lawn from a few metres away.
Installation Steps
Clear and prepare the ground. Strip the old surface, remove roots, stones and any soft spots, and level what is left. The base beneath pet artificial grass needs to be firm and free-draining before anything else happens; on clay or badly drained ground, plan the drainage first.
Measure and mark out. Measure the area in square metres, run string lines to keep the edges straight, and decide where the seams will fall. Keep joins out of gateways and away from the busiest line of travel, then add a trimming allowance at every edge.
Build the sub-base. Lay and compact a crushed stone or aggregate sub-base, then cover it with a weed membrane. Give the base a fall towards a drain, a soakaway or the garden so rain and wash-down water leave the run instead of sitting under the backing.
Roll out and cut in the turf. Unroll the turf across the area and let it relax before cutting, then trim with a sharp blade against a straight edge. On artificial turf for dogs the seams take concentrated traffic, so join the panels with seam tape and adhesive, brush the pile away from the join as you close it, and keep the join tight.
Infill with silica sand and rubber granules. Where your specification includes infill, spread kiln-dried silica sand first and work it into the base of the pile, then add rubber granules for resilience and brush both in. Not every pet installation is infilled: infill changes the feel underfoot and the way debris sits on the surface, so confirm the dressing against the sheet you are working to.
Brush and finish the surface. Brush the whole area, trim the edges into the kerb, edging or angle, and fix the perimeter down. A final brush in two directions settles the pile and shows up any patch that needs re-dressing.
Hand over and set the routine. Walk the finished surface with the person who will look after it, point out where the water runs, and agree who lifts waste, rinses and brushes. Installation is normally carried out by your own crew or a local contractor; as a custom pet turf supplier we provide the turf and the specification, and we are glad to answer questions while the job is live.
A 20 mm cut pile is the pile height that suits a roofed space. Grooming salons, indoor play barns, covered runs, converted farm buildings used as kennels and clinic exercise rooms all work with this roll, and the surface itself does not change: it is the same pet friendly artificial grass you would lay outside, on the same PP net and SBR latex backing. Two things do change — the base underneath and the way the area is cleaned — and both are decided before the first roll is opened. On a sealed concrete floor, the slab has to be sound, flat and dry. New concrete needs time to dry out, and a slab that is still holding moisture will keep that moisture under a backing that does not breathe, which shows up later as a damp patch and a smell that rinsing will not shift. Walk the floor before laying, grind or fill any high spot that would show through a 20 mm pile, and let your installer confirm the slab is dry enough for the turf to go down. Water is the other difference. Outdoors, rain flushes the pile and the sub-base for you. Indoors, nothing does. Plan the fall towards a gully, a channel drain or a doorway before the turf goes down, and rinse in that direction. Where the floor is dead flat with no drain at all, rinse lightly and pull the water up with a squeegee or a wet vacuum rather than flooding the area and leaving it wet. A hard floor gives the roll nothing to grip. Outdoors the sub-base and the edge restraints hold the perimeter; on concrete or screed, the edges need mechanical restraint — an edge trim, a steel angle or a bonded perimeter, agreed with whoever is fitting it. Rolls laid loose on a polished floor creep under traffic and open at the joints, and an open joint in a kennel building collects exactly what you do not want it to collect. Because a covered building has still air, drying matters as much as washing. Lift solids as soon as they appear, rinse the patch and then let it dry properly before the area is used again; a surface that stays damp through the day is where odour starts, long before the fibres themselves are the problem. Brushing once a week keeps the pile upright and helps air reach the base. Two smaller points worth deciding early. Over concrete, a shockpad under the turf makes a real difference to dogs that lie down for hours at a time, and the short pile on top of a pad is a better balance than a deep decorative pile, which holds debris and takes longer to dry. And tell us at quotation that the turf is going indoors, with a simple floor plan showing doors and drains, so the roll lengths and the fixing detail are planned around the building rather than around the yard outside.
- Measure in rectangles, not in one figure. Break an L-shaped or angled run into rectangles, measure each at its widest point and add them up. Note gates, drains, bowls and fixed obstacles on the sketch so the panels can be planned around them rather than discovered on site.
Order with a trimming allowance. No run is perfectly square and no wall is perfectly straight. Agree the allowance with your installer; ordering to the exact measured figure leaves nothing to trim back against a straight edge, and a shortfall is a second production run and a second shipment.
Keep the pile direction the same on every roll. The fibres lean one way, so rolls laid facing differently read as a different shade at the seam depending on which way you look. Mark the direction on each roll before anyone cuts.
Put the seams where the traffic is lightest. Keep joins out of gateways, away from the bowl line and away from the route dogs take between the two. A long straight seam along one side is always better than several short joins across the middle of the run.
Confirm the roll format before you finalise the area. Roll widths and lengths are set when you order, so send the run dimensions with the enquiry and we will confirm how the panels of 20 mm pet turf can be laid out to cut waste and keep the joins to a minimum.
Set out the edge line before the turf is cut. Fix the kerb, timber edging or steel angle first and measure its length as its own item. Cut the turf to the finished edge, not to the excavated edge, or the last 50 mm of every side ends up short.
Send a drawing with the order. An outline with dimensions, squared-up lines, door swings, drain positions and the direction you want the pile to run tells us more than a square metre total. Two people measuring the same area and getting the same number twice is the cheapest check on the whole job.
Cleaning & Care
Lift solids before they break down. A scoop and a bag first thing in the morning and again at the end of the day keeps the surface workable; leaving waste on the pile is what turns a cleanable surface into a smelly one.
Rinse, then let it drain. A hose over the area once a day moves residue through the pile and into the sub-base. Standing water after a rinse means the base is not draining and needs attention, not more rinsing.
Brush against the pile once a week. A stiff yard broom worked against the direction of the fibres lifts flattened patches and evens out the surface. It takes minutes on a run of this size and is the single habit that keeps the pile looking uniform.
Keep cleaners mild. Warm water and a mild detergent for spots, rinsed away afterwards. Bleach, solvent cleaners and a pressure washer held close to the surface will damage the fibres and the backing, and none of them are needed for the kind of soiling a pet area produces.
Treat persistent odour at the base. If a smell survives rinsing and brushing, the sub-base under the turf is usually holding water. Check the falls, lift an edge if you have to, and treat the patch with an enzyme-based cleaner rather than covering the smell with disinfectant.
Inspect seams and edges each season. Seams carry the weight of every dog that crosses them and edges take the impact of every broom. Re-glue a lifting seam while it is small and check that the edge fixings still hold before winter.
Move the furniture. Beds, bowls and agility equipment create fixed wear points. Rotating them around the run spreads the load, and a soft artificial grass surface like this one recovers its appearance faster when the traffic is not always in the same square metre.
Specifications
Grass height
20 mm
Fibre material
PP + PE
Density
16,800
Yarn weight
8,800 d
Backing
PP net + SBR latex
Pile style
Dense cut pile, modern style
Colour
Customized to your reference
Form
Supplied in rolls
Typical use
Pet runs, kennels, day-care yards and pet friendly artificial grass areas
Model
QS004
Appearance & Custom Colour
The finish is a dense, even cut pile in a deep, low-sheen green — the look most buyers mean when they say modern. There is no long shaggy thatch and no yellow fleck, so from standing height the surface reads as a closely mown lawn and settles into a scheme built on grey paving, charcoal decking, black fencing or white render. On a pet run beside a house or at the front of a boarding facility that matters, because the area is usually visible from the kitchen window or the car park.
Colour is made to order rather than pulled off a shelf. Send a reference — a paving offcut, a photo of the lawn you are replacing, a shade card, or the approved sample from your last order — and the roll is produced against it. Consistency across rolls matters more than most buyers expect: an area laid from two different runs can show a step in tone at the seam that no amount of brushing will hide, so keep the approved sample on file and check it again at each repeat order.
A pet friendly artificial grass does not have to look utilitarian. The density here carries the look, because the fibres are set closely enough that the surface reads as solid rather than sparse — which is what makes it usable in front of a showroom window or along a grooming salon's glass.
As a custom pet turf supplier we build this model for buyers who need their own shade rather than a stock green, and the same care applies at the boundary: cut edges finish cleanly against timber edging, a concrete kerb or a steel angle, so the outline of the run looks deliberate rather than cut short.
One caution we give every buyer: judge the shade under the light where it will be installed, not under the lights of an office or a warehouse. Ask your sales contact what is available to check a colour against before the order is placed.
Related Models & Mixed Orders
Pet orders rarely travel alone. The containers we load for kennels, clubs and distributors usually carry a second or third surface, and four models come up again and again beside this one: the 8 mm soft putting green QS073 for practice and hospitality areas, the 10 mm golf durable artificial grass QS072 for golf schools and hitting bays, the 45 mm soccer field turf QS071 for club pitches, and the 45 mm sport outdoor turf QS070 for multi-use games areas. There is a practical reason for combining them. Sea freight, documents and port handling are charged once, so a container carrying pet turf for one customer and putting green for another spreads those costs across more square metres — and everything arrives on the same date. If you buy wholesale artificial grass for pets to resell, this is also how you build a range rather than a single line: a pet roll, a landscape roll and a sports roll in the same shipment, in shades that sit together on a price list. Tell us the mix you want and we will confirm what can travel together.
Ordering & Shipment
Minimum order: 2,000 sqm, one container. We quote this model at container scale, so 2,000 sqm is the smallest quantity we build.
Production: 7-15 days. Production time runs from the point where colour, roll specification and quantity are confirmed in writing.
Shipping: about 30 days by sea. That is the sea leg; the door-to-door schedule depends on the destination port and customs clearance at your end.
Packed as netted rolls on cores. Each pet artificial grass roll is wrapped in netting over a cardboard core and labelled, then loaded and braced inside the container so the rolls travel without shifting.
Five-year warranty as quoted for this model. Confirm the cover that applies to your order with your sales contact when you place it.
See the run before it ships. Ask your sales contact for the production video of your order so you can check colour and pile before the container is closed.
One contact from quotation to loading. Whether you are a distributor building a wholesale artificial grass for pets range or a contractor fitting a single kennel yard, one person follows your order through.
Quality Control & Inspection
Working as an export specialist from Nantong, Jiangsu, we build quality checks into every stage of an order rather than leaving them to the end. Before bulk production, yarn, colour and backing are confirmed against the approved sample; during production we check pile height, density, tufting and backing at the supplier; before loading, rolls, colours and packing are checked again and the inspection record is shared with you. If you prefer an independent eye, we can coordinate third-party inspection such as SGS or BV, book the visit and follow up on any defects found. Faulty rolls are replaced or credited before shipment, and each carton leaves with its packing list and inspection sheet.
FAQ
Can it be laid in a covered run or an indoor play area?
Yes. Pet artificial grass is regularly laid in grooming salons, indoor play barns and covered runs; what changes indoors is the base and the cleaning. The surface needs a firm, dry sub-base and some ventilation, and because rain will not wash the area, waste should be lifted daily and the surface rinsed. If the turf is going over a sealed concrete floor, tell us before ordering so we can talk through base and drainage options with you.
Will it look right in a small garden run beside the house?
That is the setting this finish was chosen for. The dense, low-sheen pile reads as a mown lawn rather than a plastic carpet, and the short pile keeps the surface in scale with a small run and produces fewer seams. Trim it against paving, sleepers or timber edging and the boundary looks deliberate from the house.
How is it different from the landscape turf you supply?
The fibres and backing are the same family, but the two are chosen for different wear. Artificial turf for dogs takes concentrated traffic at gates and bowls, more moisture and more brushing, so cleanability and pile recovery matter more than a wide, perfectly even colour field. Landscape models are judged on colour consistency across a large area; this one is judged on how it stands up to a dozen animals a day.
How soft is it underfoot compared with a deeper pile?
On its own, a 20 mm pile is firm with some give, and most of the soft artificial grass feel comes from the PE in the blend and from what goes underneath. If dogs will lie on it for hours, or it is going over concrete, a local installer can fit a shockpad before laying the turf. Deeper piles feel softer but hold more debris and take longer to dry.
Can the rolls carry our own brand?
Yes. As a custom pet turf supplier we print labels to your artwork and wrap them so the branding shows when the rolls are stacked on site. Send the artwork and the wording you want, and approve a proof before production begins.
What should be confirmed before the rolls are made?
Four things decide whether the container matches the job: the colour, checked against a physical sample rather than a screen; the roll widths and how the seams will fall on site; whether the installation will be infilled, since that changes the dressing and the cleaning routine; and how the edges will be fixed. Send those details with the area in square metres and the order can be built around them.