This is a 40 mm tufted football turf, built on a polyethylene face yarn with a three-layer backing of polypropylene, net and SBR latex. The pile is cut level across the full roll width, the blades stand upright after brushing, and the green holds the same tone from one roll to the next — the detail that decides whether a finished pitch reads as one surface or as a patchwork of separate deliveries.
Clubs, schools and contractors settle on a football field artificial turf at this height for a reason. Forty millimetres is long enough to hold infill and give a natural-grass feel under the stud, and short enough to stay quick, drain freely and hold its shape through a heavy training calendar.
Most of these rolls go into a new build or a replacement programme. The old surface comes out, the base is checked and re-levelled, and the new artificial turf soccer field goes down in panels with the lines cut in and seamed. Whether the site is a fenced stadium pitch or a school field used by five year groups a day, the installation logic is the same — and it is the roll-to-roll consistency that keeps the joints invisible and the infill depth even. In sports academies and schools where daily training and multi-functional use are frequent, the surface is durable and low-maintenance while meeting safety requirements and sport-specific performance criteria. Its waterproof construction and robust fibers allow continuous use under heavy foot traffic and weather exposure, and it integrates with existing athletic infrastructure for faster installation and replacement cycles. It also accommodates different training drills and match conditions, helping reduce downtime and upkeep while keeping training schedules running.
Yarn and Backing Construction
The face is polyethylene, not polypropylene. PE is the softer of the two polymers used for sports yarn and the one that recovers its shape after a stud presses it down, which is why it carries the football side of the range while PP does the work on the shorter golf and multi-sport surfaces. Colour is spun into the yarn rather than coated onto it, so a scuff lifts fibre instead of exposing a pale patch underneath. Rolls for a single project are produced from one yarn lot and one colour batch. That is the unglamorous part of a wholesale artificial turf grass order, and it is the part that decides whether a 4,000 sqm pitch matches the sample a committee approved three months earlier. We have kept the same artificial sports turf manufacturers on this construction for years, so tufting gauge, latex coat weight and backing tension do not quietly drift between orders. When you re-order the model for a second site, you get the surface you already signed off. Underneath, three layers do three jobs. The polypropylene layer carries the tensile strength and stops a panel stretching out of shape under drag. The net locks the dimensions in both directions so the roll does not creep at the seams. The SBR latex is needled through the tuft roots and cured, so a fibre breaks before it pulls out — the failure that shows up as bald patches along a goal line. That same latex layer is what lets moisture pass down into the base instead of sitting under the pile. - Bonded backing that survives handling — the three layers are bonded before the roll is wound, so unrolling, dragging and re-role on site do not separate the net from the latex. Edge delamination is the first thing that ruins a pitch, and it is the first thing this construction is built to prevent. - Dimensional stability under load — the net layer holds a panel to its cut size, so the surface does not ripple in front of goal or open at a seam after a season of sliding tackles. On an artificial grass for soccer surface, that stability is what keeps the ball running true across a joint instead of kicking sideways. - A drainage path rather than a waterproof sheet — water passes through the pile, through the permeable latex backing and into the base, rather than sitting in a film across the centre circle. It is the difference between a pitch that is playable an hour after rain and one that waits for the sun. - Works with shock pads and levelled sub-bases — the backing sits flat on a compacted base and can be laid over a shock pad where the project specifies one, so the same roll serves a community field and a higher-impact performance pitch. - Panel layout on a roll system — rolls are cut to the panel widths your layout needs, so seams can be planned onto the lines and away from the busiest parts of the pitch. - Anti-static and anti-UV treatment — a 40 mm artificial grass surface carries a UV stabiliser and an anti-static finish, so it sheds dust rather than holding it, resists static cling and keeps its colour through long, bright summers. The 40 mm pile height and 10,500 lbs density are selected to balance softness and resilience, helping reduce injury risk while supporting player performance. The PP face yarn and triple-layer PP, net, and SBR latex backing support dimensional stability and water drainage, with customization in color and pile density for different sport codes, including soccer. The product carries a five-year warranty and is built for long-term durability and UV resistance in line with recognized industry standards for synthetic turf systems.
Playing Performance and Value
On the pitch, the surface behaves the way players notice before they can name it. The ball rolls at the same speed across the whole area, comes off the surface with a live bounce rather than the dead thud of a worn carpet, and holds its line when it is played along the ground. Studs go in and come out cleanly, which is the difference between a player turning and a player going over.
Consistency is the whole point on a 40 mm artificial grass pitch. A pass reaches the same speed in the first minute and the eightieth, and a bounce does not change because one panel is two seasons older than the next. On artificial turf football fields used for competitive fixtures, that predictability is what players and referees actually judge.
Where the value lands is cost per season. A surface that stays playable through winter and does not need a renovation window every summer spreads its purchase price across years of fixtures — and that calculation, rather than the square-metre rate, is usually what carries a committee vote.
Multi-Sport and Indoor Use
One surface, several sports — if the line set is agreed first — football, five-a-side, futsal training and school games all sit comfortably on 40 mm artificial grass with a sand and rubber infill. The limit is rarely the pile; it is the markings, so if the site also needs a small-sided layout, settle the second line set before the rolls are cut.
Where the surface stops being a football pitch — court games want a lower, faster bounce from a shorter pile. A basketball or tennis line on soccer artificial turf will always read slower than on a purpose-made court, so where a school needs both, keep the court on its own part of the site rather than marking one surface for everything.
Indoors the backing is the same, the base is not — the yarn and the three-layer backing are waterproof, so an indoor hall takes the same roll as an open pitch. What changes is underneath: a flat, dry sub-floor instead of a drained aggregate base, and edge fixing into the building instead of into a kerb.
Infill depth is the dial — a shallower sand and rubber layer gives a livelier, quicker surface for small-sided games and training drills; a fuller layer gives the softer, natural-grass feel a full-size pitch wants. Fix the sports list before the infill depth is confirmed, and the depth follows from it.
Indoors, brushing replaces the weather — outdoors, rain washes grit down through the pile; in a hall nothing does, so a scheduled brush and a vacuum take over that job. The anti-static finish in the fibre helps here, shedding dust instead of holding it.
Ventilation matters more than shade — a covered pitch stays cooler than an open one in summer, but still air is what players notice. A light mist before a session and a through-draught do the work that a watering does outside.
Waterproof still needs somewhere to drain — the backing passes water into the base rather than sealing it, so an open multi-use area still needs its falls, its membrane and its outlet built into the groundworks.
How to confirm the fit — send the sports you want on the site, the sessions per week for each and whether it is indoors or out, and we will say what this construction handles and where a second, shorter surface is the better buy.
Installation Sequence
Site preparation — strip the old surface, clear roots and debris, confirm the falls the base will need, and set the edge restraints that will hold the perimeter. Check access for a delivery vehicle before the rolls arrive; a full container needs room to be unloaded and staged near the pitch.
Measuring and setting out lines — set out the pitch with string lines and mark the centre circle, penalty areas and goal lines before any turf is cut. Decide where the seams will fall at this stage, keeping them out of the goalmouths and away from the busiest corridors.
Laying the base — compacted aggregate with a geotextile membrane, plus a shock pad where the specification calls for one. Check levels with a straight edge and test the fall across the whole area; an artificial grass for soccer surface has nowhere to hide a hollow.
Laying the turf — let the rolls relax, lay them in the direction of play, and cut each seam on a straight edge before gluing it over seam tape. Lines are inlaid as contrast strips rather than painted, so they stay sharp through the life of the pitch instead of wearing away in the goalmouth.
Infill with silica sand and rubber granules — spread the sand first with a drop spreader and brush it into the pile, then add the rubber granulate to the depth confirmed for your project. Work in dry conditions; wet fibre will not take infill evenly.
Brushing and finishing — power-brush against the pile direction to lift the fibres, trim the perimeter, and check that infill depth is even across the pitch rather than thick in the middle and thin at the corners.
Acceptance and handover — walk the pitch with the installer and check seams, lines, infill depth, drainage and edge fixing, then agree a brushing schedule and a maintenance plan before the first fixture.
Care and Maintenance
Brush against the pile — a power brush or a stiff drag brush once a week in season lifts the fibres and redistributes infill that collects in the goalmouths. On 40 mm artificial grass, brushing is the single action that keeps a surface looking new.
Top up the infill — rubber granulate migrates and compacts over time. Measure the depth at a few fixed points each season and bring it back to the level agreed for your project; that depth figure should come from the artificial sports turf manufacturers who supplied the roll, not from a rule of thumb. Low spots are where the pile starts to lay over.
Keep the surface clear — leaves, grit and wind-blown litter block the drainage path. On soccer artificial turf, grit carried in from a neighbouring path is the usual culprit behind a wet patch that appears after rain.
Deal with spills early — most marks lift with warm water and a soft brush. Chewing gum and oil need a turf-safe remover, and it is worth testing any product on an off-cut before it goes near the pitch.
Check seams and edges each season — walk the perimeter and the glued joints looking for lifted edges or opened seams. Small repairs done early cost far less than a panel replacement.
Watch the traffic zones — goalmouths, corners and the technical area take the most wear. Rotating training drills and keeping portable goals off the same spot spreads the load.
Plan for hot days — the surface stores more heat than natural grass in direct sun; a light watering before a session cools it down and improves slide.
Professional Venue Installations
Full-size stadium pitches — laid over a levelled base with the lines inlaid, the surface matches the touch and ball behaviour of good natural grass closely enough for competitive fixtures, without the close-season renovation cycle that a grass pitch demands.
Club complexes with academy and warm-up pitches — using the same construction on the main pitch and the outer pitches keeps coaching drills transferable and lets grounds staff run one maintenance routine across the whole site.
Covered and indoor arenas — the turf is waterproof and dimensionally stable, so an indoor artificial turf soccer field keeps its lines and does not lift at the seams in a humid hall.
Venues with under-pitch heating or irrigation — where the base design includes those services, the permeable backing and panel layout let the turf sit over them without trapping moisture underneath.
Multi-event and broadcast venues — consistent colour and pile direction matter when a camera pans across a seam, and roll-to-roll matching is what keeps artificial turf football fields looking like one surface on screen.
Tender and federation clauses — if your project is written against a national federation or league standard, send us the clause and we will tell you what can be documented for the supply and what has to come from the installer or an independent test house.
School and Training Grounds
A school pitch is a harder test than a stadium. It takes five classes a day, a lunchtime five-a-side and an after-school club, and it is expected to look presentable on parents' evening. This model handles that rhythm because the pile recovers, the infill can be topped up locally and the surface stays playable in light rain instead of being called off.
For academies and colleges the practical question is repeatability. The artificial sports turf manufacturers behind this construction run the same tufting and latex settings across re-orders, so a second pitch bought two seasons later behaves like the first and a coach does not have to relearn how the ball rolls.
Schools and clubs often buy through a local contractor or a distributor who already holds wholesale artificial turf grass stock, which is the quickest route for a single pitch. On larger or tendered projects the turf usually comes in directly against the confirmed specification, with the layout and line set agreed before cutting.
Safety is the other half of the brief. A 40 mm pile with a correctly specified infill gives enough give to take the sting out of a fall without turning spongy underfoot, and the surface stays clear of the puddles and frozen patches that close a grass field in February. Our artificial football grass uses polypropylene face yarn with a PP net and SBR latex backing for durability, stability, and wear resistance on sports fields and training grounds. Color, pile height, and density can be customized to project requirements, and bulk production typically takes 7 to 15 days depending on order size and specifications, with packaging and logistics coordinated for delivery.
Specifications
Primarily used in football field installations, training grounds, and multi-purpose sports complexes, this turf performs consistently in varied weather and suits professional arenas as well as amateur and school environments for safe, year-round use. Its waterproof, eco-friendly composition reduces maintenance and integrates with existing sports facility infrastructure, while the modular design helps speed installation and supports scalable procurement. These operational benefits make it an economical choice with strong return on investment for clients worldwide.
Property
Value
Pile height
40 mm
Face yarn
Polyethylene (PE)
Yarn weight
10,000 dtex
Pile density
10,500, as listed on the specification sheet
Backing
Three layers — polypropylene, net, SBR latex
Pile construction
Tufted, cut pile
Colour
Produced to your specified colour
Surface treatment
Anti-UV and anti-static
Drainage
Permeable backing; water passes through to the base
Primary use
Football pitches, training grounds, school fields
Indoor and outdoor
Both
Ordering and Delivery
Minimum order — 2,000 sqm, which fills one container. It can be a single model or a mix from the range, so a site that needs a pitch and a putting green fills the same box.
Production time — 7–15 days from the point your specifications and colour are confirmed. Colour approval starts the clock, so sign off a piece before the order is released.
Shipping — about 30 days by sea. Transit varies with port and route, and we confirm the sailing against your booking.
Warranty — five years on the turf as supplied, under the terms issued with your order.
Pricing — quoted per square metre against your confirmed specification and destination port. Send the pitch area, layout, infill requirement and port, and you get a figure rather than a range.
Samples and approval — ask your sales contact about sample availability and lead time before the specification is locked; a physical piece is the only reliable way to sign off colour against a club or tender reference.
Roll form and labelling — the turf ships as wholesale artificial turf grass in full production rolls, wrapped for transport and labelled by model and colour so the installer can match panels to the layout without opening every roll.
Order reference — quote QS017 with your layout so the pile height, backing and colour are pulled against the right construction.
The football line continues either side of this model. The 45 mm soccer field turf (QS071) and the 45 mm outdoor sports turf (QS070) carry a deeper pile for buyers who want a heavier surface or a different infill regime, while the shorter work is handled by the 10 mm durable golf turf (QS072) and the 8 mm soft putting green (QS073) for practice greens and short-game areas. If a project needs something shorter than this 40 mm artificial grass — a multi-use court, a warm-up strip or an indoor hall — say so when you send the layout and we will point you to the right construction rather than the nearest one. Tell us the sport, the sessions per week and the base you already have, and the recommendation comes with the reason attached.
Quality Control & Inspection
Working as an export specialist from Nantong, Jiangsu, we build quality checks into every stage of an order rather than leaving them to the end. Before bulk production, yarn, colour and backing are confirmed against the approved sample; during production we check pile height, density, tufting and backing at the supplier; before loading, rolls, colours and packing are checked again and the inspection record is shared with you. If you prefer an independent eye, we can coordinate third-party inspection such as SGS or BV, book the visit and follow up on any defects found. Faulty rolls are replaced or credited before shipment, and each carton leaves with its packing list and inspection sheet.
FAQ
What materials are used in your artificial football grass?
The face is polyethylene — a softer, more resilient polymer than polypropylene, which is why it carries the football side of the range. Underneath sits a three-layer backing: a polypropylene carrier for tensile strength, a net that holds the panel to its cut size, and SBR latex needled through the tuft roots and cured so the fibres stay put. The yarn is finished with UV and anti-static treatments, which is what a football field artificial turf needs to keep its colour and shed dust rather than hold it.
Can I choose the colour and specification?
Yes. Colour is produced to the reference you supply, and pile height, density, backing and roll widths are agreed before production starts. Custom work on an artificial grass for soccer order is routine for us — most projects carry a club colour, a tender clause or a pitch size that is not standard. Send the reference and the layout, then approve a physical piece before the bulk run is released; that is the step that prevents a colour argument three months later.
Is the turf suitable for both indoor and outdoor use?
Yes. The yarn and backing are waterproof, so the same roll works on an open pitch and inside a hall. Two things change with the setting: outdoors the base needs a fall and a drainage route, while indoors you plan for a flat sub-floor and the fact that an indoor artificial turf soccer field gets no rain to wash dust through, so brushing and vacuuming matter more.
How does 40 mm compare with a 50 mm pitch or a shorter pile?
Forty millimetres with a sand-and-rubber infill covers the majority of club, school and community pitches — it gives a natural-grass feel without the extra infill volume a deeper pile asks for. A 50 mm construction is usually chosen for higher-level or heavily funded venues. Shorter pile belongs on multi-use courts and training strips where ball speed matters more than cushioning. If you are weighing up soccer artificial turf for a specific level of play, tell us the level and the sessions per week and we will say which height we would put on it.
What base and infill does the turf need?
A compacted aggregate base with a fall, a geotextile membrane and edge restraints, plus a shock pad where the project specifies one. Infill is silica sand followed by rubber granulate, and the depth is confirmed against your level of play rather than assumed — too little and the surface stiffens, too much and it turns soft and slow. We can send the base detail that matches this construction for your groundworks contractor.
Can the same surface be used for more than football?
Within reason. Across artificial turf football fields used for more than one sport, the limiting factors are the line markings and the infill depth — a surface built for football is slower than a court surface and too soft for a ball that needs a low bounce. Multi-use pitches are normally specified with a shallower infill and a line set agreed up front, so decide the sports list before the turf is cut.
How are the lines and seams handled?
Lines are inlaid as contrast strips rather than painted on, so they do not wear away under studs. Each seam is cut on a straight edge, taped and glued, and seam positions are planned onto the lines wherever the layout allows so the join disappears into the marking. Keep seams out of goalmouths and the busiest corridors — a good installer lays it out that way before a single roll is cut.