As a soccer field turf manufacturer working with clubs, contractors and importers, we build this surface for grounds that play every week rather than a few times a season. Polyethylene blades are tufted densely into a PP + net + SBR latex backing, in two green tones, so the pitch still reads as grass from the stands and not as one flat sheet of colour. The pile depth is set to take a sand and rubber infill layer without the blades disappearing into it.
Step onto an artificial turf soccer field built on this system and the first thing most coaches notice is the footing: blades that stand up under studs instead of lying flat by the second month. That comes from the yarn, the tufting density and the latex bond that locks each tuft into the backing. The ribbed black backing shows at every roll edge, so your installer can check the latex coat and the net layer before a single roll is opened.
Typical projects for a 40 mm artificial grass soccer field are club pitches, school and university fields, community sports parks and resurfacing work where the old carpet has gone flat or stopped draining. Roll sizes are agreed per project, so the layout follows your drawing rather than a standard sheet length.




The face is polyethylene, the yarn family we use for outdoor football surfaces because it stays soft underfoot in heat and cold and takes colour evenly along a full production run. We build this PE synthetic soccer turf on a yarn weight and density that sit in the middle of our football range: firm enough for a stud to bite, forgiving enough that a fall does not feel like concrete — the balance a soccer field turf manufacturer has to strike.
Underneath, three layers do three separate jobs. The polypropylene sheet gives the roll its dimensional stability, so it does not creep or shrink across the length of a pitch. The net layer takes the pull at seams and edges, which is where turf normally fails first. The SBR latex coat bonds the tufts from below and holds them through brushing, infill work and years of studs; because it is applied as a ribbed profile, water moving down through the pile spreads across the back rather than sitting against the bond.
Seeing the material before it is laid matters more than most specification sheets admit. A sample shows the dense upright blades, the two-tone green face and the black ribbed back side at once, and that backing tells an experienced installer whether the latex coverage is even. As an artificial grass supplier for soccer fields we also check the base story: if you are moving up from a shorter pile, the stone depth and infill profile change with the carpet, and it is far cheaper to settle that before the rolls ship than after they are unloaded on site.
- Two-tone green pile — two shades are tufted together, so foot traffic, sunlight and wear do not leave the surface looking patchy after a season of use. - Dense, upright blades — close tufting keeps the pile standing under studs rather than lying down by mid-season. - Filled build — the pile leaves room for a sand and rubber infill layer, so the finished feel is set at installation instead of being fixed at the factory. - Consistent specification — pile height, yarn and backing sit on one specification sheet, and as an artificial grass supplier for soccer fields we hold that sheet, so a reorder months later matches the first container. - Custom colour from one source — the standard dual-tone green can be adjusted to club or project colours, and yarn, backing and colour stay on the same production record. - Built as artificial sport turf — it handles football training, warm-ups and light multi-sport sessions where one field has to serve several programmes.
| Model | QS016 |
|---|---|
| Pile height | 40 mm |
| Yarn material | Polyethylene (PE) |
| Yarn weight | 10,000 d |
| Density | 10,500 lbs |
| Backing | PP + net + SBR latex |
| Construction | Tufted, filled system |
| Colour | Customized; dual-tone green shown |
| Blade appearance | Dense, upright green blades |
| Typical use | Soccer pitches, training grounds, multi-sport areas |
| Supplied as | Rolls, size agreed per order |
| Pile height | What it changes |
| Playing feel | Typical applications |
| Cost and confirmation | 40 mm (QS016) |
| Sand and rubber infill, with depth set by the system you order; top up goalmouths and the centre circle as granulate migrates. | Firm, stable footing and a lower, quicker surface; ball roll stays predictable once the infill is brushed in. |
| Club and school pitches, community fields and multi-use grounds; a common choice at this height. | Lowest carpet and infill cost of the three; around 2,000 sqm fills one container. Confirm yarn weight and infill profile for your base. 45 mm build |
| More infill per square metre than 40 mm, so sand and rubber volumes rise and brushing takes longer. | Slightly deeper and softer underfoot, with more room for the blade to flex under studs. |
| Clubs and academies wanting a more cushioned artificial turf soccer field without the longest pile. | Mid-range carpet cost plus a larger infill order; confirm the pile height and density on the specification sheet for the model you order. 50 mm build |
| The largest infill volume of the three; allow more sand and rubber and a longer installation window. | Deepest, slowest feel in the range, closest to a stadium surface; stud release depends on correct infill depth. |
| Stadium and show-field projects where a premium surface is part of the brief. | Highest carpet and infill cost; extra depth also affects roll volume and container loading. Ask for the final pile height in writing and a sample of the exact yarn. |
Brushing is the main maintenance job on any artificial surface: a power brush or a stiff drag mat lifts flattened blades and pushes infill back where it belongs. Owners choosing eco friendly artificial grass for a school or a public park usually have a small grounds team, so the routine is kept deliberately simple — brush the goalmouths and the centre circle more often than the rest of the field, because those are the places the pile lies down first.
The surface also needs its infill topped up as granulate migrates or compacts. Keep the level even, because thin patches change how the ball rolls and how the surface takes a stud. Clear leaves and debris from the drainage paths before the wet season, check seams and perimeter fixings once a year, and keep hot works, barbecue trays and vehicle traffic off the surface.
Keep a small stock of the same infill on site for spot top-ups, and record what was installed — sand grade, rubber type and depths — so a later order matches. If a seam lifts or a section of pile stays flat after brushing, photograph it and raise it with us early rather than waiting for the next season.
Working as an export specialist from Nantong, Jiangsu, we build quality checks into every stage of an order rather than leaving them to the end. Before bulk production, yarn, colour and backing are confirmed against the approved sample; during production we check pile height, density, tufting and backing at the supplier; before loading, rolls, colours and packing are checked again and the inspection record is shared with you. If you prefer an independent eye, we can coordinate third-party inspection such as SGS or BV, book the visit and follow up on any defects found. Faulty rolls are replaced or credited before shipment, and each carton leaves with its packing list and inspection sheet.